Canon MX492 Setup Guide For Windows

The Canon printers come in the wide range. Depending upon your choice whether you need it for the printing only, or for a multipurpose, you can buy it. Therefore, if you need the multipurpose one in which you can print, fax or scan, then Canon MX492 is best. So, to use it, you need to complete the Canon MX492 Setup so that software can be installed in the system. In this blog, the steps for the Canon MX492 Setup are explained for the Windows operating system. Moreover, every step has been explained in detail so that you don’t get confused with the setup of Canon MX492. This includes the steps from the hardware setup to the driver installation. Sp, you can say that it is the guide from the scratch for the Canon MX492 printer. So, let’s get started!

Steps For Canon MX492 Setup

The setup procedure for the printers is not difficult if done in the right sequence. Therefore, now the steps for the Canon MX492 printer setup is defined from the unboxing to the driver setup. So, just follow the steps as mentioned below one by one:

1. Unboxing And Hardware Setup For Canon MX492 

Step 1: Find a flat surface near to the system and router, and place your Canon MX492 printer there.

Step 2: Then, unbox your Canon MX492 printer from the box, and also remove all the coverings and tapes.

Step 3: After that, connect it to the power source.

Step 4: Next, power on your printer by pressing the power button over your Canon printer. 

Step 5: Wait for the green Power LED to get stable.

Step 6: If there is orange or red LED instead of the green, then it means there are loose connections. So make sure to secure the connections again for the power supply.

Step 7: Once, the green LEd is lighting, then attach the paper tray carefully for the printer, and insert the right sheets.

Step 8: Next, if the printer is in idle condition, then open the access door, and insert the cartridges carefully. Close the door for the ink cartridges after their proper installation.

Step 9: Wait for the alignment to be dien properly by the Canon printer itself.

So, these are the steps for the unboxing and hardware setup for the Canon printer. Now, the next step is to complete the network configuration for the Canon printer. 

2. Network Configuration For Canon MX492 Printer

Completing the network configuration for the Canon MX4932 printer means to connect the printer with the wireless network. Therefore, follow the steps as mentioned below:

Step 1: Before you start with the network configuration process, make sure the power light i.s. green LEDs should be stable.

Step 2: Now, search for the Setup button on the Control Panel of your printer.

Step 3: On the display of the printer, the Setup menu will be open.

Step 4: Select the option of the Wireless Lan setup option from the menu.

Step 5: Next, press the OK button.

Step 6: Then, further in the Wireless LAN Setup menu, tap on the “Other Setup” option.

Step 7: Again, press the OK button.

Step 8: Further, choose the option of the “Cabless/Cableless Setup” and press the OK button again.

Step 9: Wait for some time, till your printer gets connected automatically to your home network. 

Step 10: It may also display the list of the networks available for the connection, and select the name of your network.

Step 11: Enter the password as well if required, and complete the network configuration for the printer.

Once your printer is connected to the network, then the network configuration part for the Canon MX492 printer is completed. Now, you are left only with the last phase i.e. Driver installation.

3. Install Printer Driver for Canon MX492 Setup

Now, with the printer driver installation, the Canon MX492 process is about to complete. So, let’s have a look of the last steps for the Canon printer driver installation:

Step 1: First, you need to connect your system to the same network with which you have connected the printer.

Step 2: Next, you should open the browser in your system, and visit the link canon.com/ijsetup.

Step 3: You will land on the setup page for the Canon printer.

Step 4: Next, search for the yoru printer model i.e. MX492 in the search bar.

Step 5: Then, you will be redirected to the Drivers and Downloads page.

Step 6: Select the right operating system from the drop down.

Step 7: Next, click on the download link for the Canon printer driver.

Step 8: Wait for the file to get downloaded, and open the setup file after the download.

Step 9: This will open the installation wizard for the Canon MX493 printer.

Step 10: Next, select the country, region, and date on the Welcome screen, and click on the Next button.

Step 11: Further, go with the on-screen instruction to complete the setup of the printer.

Step 12: In the Connection Type window, you must select the option of the Wireless LAN Setup.

Step 13: Install the software, and click on the Finish button after installation to quit from installation wizard.

Step 14: Now, to add the Canon printer to the system, go to the Control Panel.

Step 15: Then, click on the link to Add a Printer.

Step 16: Select the name of your printer from the list and click on the Add button.

Step 17: Make the Canon MX492 printer as the default. 

Step 18: So, take a test printout and confirm the successful setup for the Canon MX92 printer.

So, this completes the setup of the MX492 printer from scratch. Now, you can take the print, scan or fax as you want with the Canon MX492 printer. Moreover, it will be over the wireless network, that means, there is no need to worry about it.

Go Multipurpose With Canon MX492 Printer!

Wrapping up! In this blog, the right sequence of the steps are explained for the Canon MX492 setup. So, it is now easy for you to observe how easy it is to complete the setup of your printer with these steps. So, without worrying much, complete the wireless setup for your printer. Therefore, once you complete the Canon MX492 Setup, then you can use it for multipurposes. In case, there is any doubt or query, contact us for the resolution. Even, our team will help you to complete the Canon MX492 setup in an easy way. Therefore, get ready to scan, print or fax with the Canon MX492 printer over the wireless network.